Product Introduction
1. Household RO Water Filter Booster Pump Item:PL-303-400W ,24V/DC ±5%
2. Features of ro reverse osmosis water filter system ro
Definition: Mainly designed for RO water purifiers used in 30 psi inlet pressures.
Product features: low vibration and low noise.
3. Cooling method: cooling by radiation
4. Technology requirement of ro filter booster pump
4.1 Structure, dimensions and tolerances. 3/8 pipe threaded interface
Household RO Water Filter Booster Pump Description
1. This drawing is for reference only, the actual size is subject to the product;
2. The compression of the suspension rubber should be controlled at 1-1.5mm;
3. The inlet and outlet diameter of the pump is 3/8 inch taper pipe thread;
4. The power cable is 20AWG×2C×L22CM with L6.2 terminal;
5. The above dimensions are in mm.
Advantages
The Household RO Water Filter Booster Pump is made just for home reverse osmosis water purifiers. It works well with a lot of different systems and gives stable boosting power to make sure that water is cleaned well. It runs with little noise and vibration, and it has radial cooling to keep the heat from building up and keep it running smoothly. The pump has interfaces that work with a wide range of devices, is straightforward to set up, and has parts that are put together perfectly, which ensures that it will seal properly and work reliably. It has safe and reliable electrical performance, enough boosting flow, and low energy use. It is a high-quality booster pump accessory for home reverse osmosis water purification systems since it won't overheat or leak and will last a long time.
Technical Requirements
1. Appearance
It is required that the surface paint of the fuselage does not fall off, the joint is not loose, and the rubber feet are not damaged.
2. Electrical strength
The power port and the casing can withstand 500V/50Hz/1min without flashover and breakdown.
3. Rated voltage DC 24V ± 5%
4. Pressurization and flow performance When the inlet pressure is 30 psi and the outlet pressure is 70 psi, the total output flow is ≥ 2200 mL/min.
5. Applicable water temperature 5°C~45°C
6. working environment temperature 5 ° C ~ 40 ° C
7. Working water pressure 30psi
8. Working current ≤ 2.2A (inlet pressure is 30 psi, outlet pressure is 70 psi)
9. Rated current ≤ 2.8A
10. Pressure resistance
It can withstand 170psi (12kg) static water pressure without deformation and damage, and there is no water leakage at each joint.
11. Outlet end strength
The lead end receives 40N pulling force along the axis for 10±1s, and the lead end should not be loose.
12. Constant damp heat test
Placed in an environment with a temperature of 40 ± 2 ° C and a relative humidity of 93% ± 3% for 48 hours, and its electrical properties after drying
Still meet the requirements.
13. Surface heating
After 24 hours of continuous operation, the surface temperature rises ≤ 50K.
14. Blocking pressure 140 PSI ± 15 PSI (inlet pressure is 30 psi, blocked by water)
15. Noise ≤ 55 dB(A)
16. Lifetime
Starts 100,000 times or 2000 hours of continuous operation, and there should be no abnormal phenomena such as water leakage, jamming, and excessive noise.
17. Water hammer resistance
After the test, it can withstand 0-1.05MPa 100,000 times water hammer test without deformation, damage, and no leakage.
18. Self-priming height: non
19. Blasting pressure ≥ 3.2MPa (454.4PSI)
Hot Tags: household ro water filter booster pump, China household ro water filter booster pump manufacturers, suppliers, factory, Household RO Water Filter Booster Pump, reverse osmosis system membrane replacement, ro filter booster pump, ro membrane replacement procedure, ro water booster pump
